seaEQ Piling Fender PF 40/80 – Large Piling Protection with Sliding Principle

Piling Protection – Without Abruptly Stopping the Boat on Contact

The seaEQ Piling Fender PF 40/80 protects the boat's hull from direct contact with mooring pilings when entering or leaving a berth and while moored.

Unlike conventional boat fenders, the PF is attached directly to the piling. This places the protection exactly where contact between the boat and the piling is likely to occur.

With a protective surface of approximately 400 × 800 mm, the PF 40/80 is particularly suitable for larger mooring pilings and berths with significant changes in water level.

The seaEQ Sliding Principle – Keeping the Boat Manoeuvrable

The decisive difference compared with rigid protection systems is the seaEQ Sliding Principle.

During sideways contact, the boat is not abruptly stopped against the piling. Instead, the hull can slide along the surface of the piling fender, allowing the boat to remain manoeuvrable throughout the manoeuvre.

This can be particularly beneficial when entering a marina berth: Contact with a piling does not suddenly interrupt the manoeuvre but allows the boat to continue moving in a more controlled manner.

Directly on the Piling – Protection Exactly Where It Is Needed

Because the PF 40/80 is mounted directly on the piling, the skipper does not need to position a loose boat fender precisely between the hull and the piling when approaching the berth.

The piling fender remains at the berth and protects the contact area whether the boat moves forwards or backwards alongside the piling during mooring manoeuvres.

Tool-Free Installation Without Drilling

The PF 40/80 is attached directly to the piling using the appropriate seaEQ PFS tensioning strap system. No drilling, screws or permanent modifications to the piling are required.

The PFS tensioning strap systems allow installation on round and square pilings. Different strap sizes accommodate a range of piling dimensions.

Important: When ordering, select the appropriate PFS tensioning strap system from the dropdown menu according to your piling dimensions. The selected PFS tensioning strap system is included with the PF 40/80.

Which seaEQ PFS Tensioning Strap System Fits My Piling?

To select the correct tensioning strap system, measure the diameter of a round piling or the side length of a square piling.

The following table shows the appropriate PFS tensioning strap systems for the respective piling dimensions.

Selection guide: Measure your piling before ordering. Then select the PFS tensioning strap system that matches your piling dimensions from the dropdown menu. The piling fender is supplied together with the selected tensioning strap system.

Three PF Sizes for Different Mooring Situations

The seaEQ PF range is available in three sizes. The most suitable model depends on the piling dimensions, expected water level changes and the individual conditions at the berth.

Durable Construction for Marine Use

The outer surface of the PF 40/80 is made from high-strength polyester fabric with a PVC coating. The material has a tested lightfastness rating of ≥ 5 according to DIN EN ISO 105-B02.

A specially designed PE foam core provides cushioning in the contact area. The piling fender is reinforced around its edges with durable polypropylene (PP) webbing, which is securely sewn into the construction.

The tensioning straps of the PFS system are guided and tightened using PET rods. This allows the entire system to be constructed without metal components.

No Metal Components in the PF Fender System

The seaEQ PF fender systems contain no metal components. This means there are no hard metal parts in the fender system that could damage the boat's hull during contact.

The PFS tensioning strap system included in the delivery is also entirely metal-free.

Care and Storage

The PF 40/80 is designed for regular outdoor use. As with other textile materials, prolonged and intensive exposure to sunlight may gradually affect the colour intensity.

To preserve the colour for as long as possible, we recommend cleaning the piling fender and storing it away from continuous sunlight when it is not in use during the off-season.

Dimensions

PF 40/80: approx. 400 × 800 × 25 mm
(Width × Height × Thickness)

Scope of Delivery

1 × seaEQ Piling Fender PF 40/80
1 × seaEQ PFS tensioning strap system in the size selected from the dropdown menu

The matching PFS tensioning strap system is included in the purchased set and does not need to be ordered separately.

Manufactured by seaEQ Germany

The piling fenders in the seaEQ PF range are manufactured in Germany. Their design, material selection and workmanship are intended for regular use at marina berths.

Frequently Asked Questions (FAQ) about the seaEQ Piling Fender PF 40/80

What makes the seaEQ Sliding Principle special?

During sideways contact with the piling fender, the boat is not abruptly stopped. The hull can slide along the surface of the PF, allowing the boat to remain manoeuvrable when entering or leaving the berth.

Where is the PF 40/80 installed?

The PF 40/80 is attached directly to the piling at the berth. This keeps the fender in the relevant contact area, so it does not need to be repositioned before every mooring manoeuvre.

Do I need tools for installation?

No. Installation is carried out using the appropriate seaEQ PFS tensioning strap system. No drilling or other permanent modifications to the piling are required.

Is the PF 40/80 suitable for round and square pilings?

Yes. The seaEQ PFS tensioning strap systems allow installation on round and square pilings. The required system depends on the diameter or side length of the piling.

Which tensioning strap system do I need?

The correct PFS tensioning strap system depends on your piling dimensions. Measure the diameter of a round piling or the side length of a square piling, then use the sizing table to select the appropriate system from the dropdown menu.

Is the PFS tensioning strap system included in the delivery?

Yes. The seaEQ PFS tensioning strap system selected from the dropdown menu is included with the PF 40/80. No separate purchase is necessary.

Is the PF 40/80 suitable for tidal marinas or changing water levels?

Yes. With a height of approximately 800 mm, the PF 40/80 provides a large vertical protective area and is particularly suitable for berths with significant water level changes. The actual protective area required depends on the berth, the boat and local water level conditions.

What is the difference between the PF 40/80, PF 40/60 and PF 25/80?

The PF 40/80 and PF 40/60 are both approximately 400 mm wide and differ mainly in height. The PF 25/80 is narrower at approximately 250 mm but also has a height of approximately 800 mm. This allows the fender size to be matched to both the piling dimensions and the water level conditions at the berth.

Does the PF 40/80 contain metal components?

No. The seaEQ PF fender system is entirely metal-free. The tensioning straps of the PFS system are tightened using PET rods.

Does the piling need to be drilled for installation?

No. One of the advantages of the PF system is that it can be attached without drilling or screwing into the piling. The fender can therefore be installed without permanently modifying the piling.

How should I care for the PF 40/80?

Dirt can be removed using water and a suitable mild cleaning agent. To preserve the colour intensity for as long as possible, we recommend cleaning and drying the piling fender before storing it away from continuous sunlight during the off-season.